SEARCH FAQ
FAQ QuestionWhere can I install solid wood flooring?
FAQ Answer
Solid wood can be installed on or above grade, but not below grade. Basements usually have high moisture levels and fluctuations in temperature making them a poor area for wood installation. Bathrooms are also a poor choice as well as any other room that may experience pooling liquid. Nail-down installation methods can be installed over wood subfloor. Glue-down and floating installations can be installed over wood, concrete or one layer of existing flooring as long as it is clean and firmly attached to the subfloor beneath. Neither should be installed over carpet and glue down is not recommended over particle board or chipboard. When installing over concrete, it is recommended that you check with your manufacturer’s recommendations and always use a moisture barrier. It is not recommended to install solid wood in tropical climates with high humidity.
top

FAQ QuestionHow much wood flooring do I need?
FAQ Answer
  1. Divide the floor into rectangles.
  2. Measure the length and width of each individual rectangle.
  3. Multiply the length by the width of each individual rectangle.
  4. Add your total for each rectangle together to get the total square footage.
  5. Add an additional 5-10% (depending on the manufacturer’s recommendations) of the total square footage to cover the waste factor. Waste factors are needed to estimate for cutting the flooring, additional material to select out pieces that don’t match (wood is a natural product and can have pieces that don’t match the majority of the floor).
  6. Use our flooring estimator tool.
top

FAQ QuestionHow can I test my room to find out if there are moisture issues with the subfloor before installing wood flooring?
FAQ Answer
There are professional devices that can be used, however when these are unavailable, tape a piece of clear plastic sheeting (Plastic) to the floor and leave it for 24-48 hours. Make sure the edges of all sides of the plastic are sealed tight to ensure that air and moisture can’t escape. When you take it off, if there is moisture on the plastic (condensation) or the floor is discolored where the plastic was, there are probably moisture issues. Consult a professional flooring installer for options before proceeding.
top

FAQ QuestionHow is solid wood normally installed?
FAQ Answer
Solid wood often comes in nail down or staple installations. There are also floating installation methods which are not affixed to the subfloor and may or may not require glue. These are rare to find due to the fact that wood expands and contracts with changes in moisture and temperature. A floating floor is locked together in one complete unit instead of being affixed to the subfloor making contraction and expansion very difficult.
top

FAQ QuestionIs solid wood flooring recommended for a self-installer?
FAQ Answer
Solid wood is moderately difficult to install and does require patience, skill, and special tools. If you attempt a self-installation it is recommended that you carefully follow your manufacturer’s recommendations and also purchase a pre-finished product that does not involve glue for an easier installation. Sanding and finishing a floor can be difficult for the non-professional. If you are unsure of your skill, it is always best to consult with a local floor installation professional.
top

FAQ QuestionCan solid wood be installed over radiant floor heating systems?
FAQ Answer
Some solid woods can be installed over radiant heating but it is generally recommended that you use engineered wood flooring because it is less sensitive to moisture and temperature changes. If using solid wood be sure to coordinate the installation of the radiant heating and with installation of the wood to ensure there will be no issues. Of the different flooring installation options, the best installation method to use over radiant heating is a floating installation without the use of nails or adhesives which if often hard to find in solid wood. The maximum temperature of the subfloor should never exceed 80 Degrees F. It is not recommend that you use maple or pecan.
top

FAQ QuestionIs it important to acclimate my solid wood flooring with the room in which it will be installed?
FAQ Answer
Yes, extremely. You should let you solid wood flooring sit unopened and flat in the room in which it will be installed for 1-2 weeks before installation. If you are installing in a room that has humidity issues, you may need to use a humidifier or dehumidifier.
top

FAQ QuestionDo I need a moisture barrier when installing my solid wood flooring?
FAQ Answer
Whether you are installing your solid wood on or above grade it is almost always recommended that you use a moisture barrier to protect your floor from any potential damage. A moisture barrier is absolutely essential when installing solid wood over a concrete slab.
top

FAQ QuestionCan I install solid wood flooring on steps?
FAQ Answer
Yes, you can install solid wood flooring on steps using a stair tread and stair riser. In some cases you can use your flooring as the stair tread along with a trim piece called a stair nose to create your own stair treads.
top

FAQ QuestionDo I need to leave an expansion gap when installing wood flooring?
FAQ Answer

Yes, it is vital to the life of your floor that you leave an expansion gap of at least ¾"around the perimeter of the room and all obstructions. Check with your manufacturer as you may need a larger or smaller expansion gap depending on the geographical region, interior moisture and temperature, and time of the year.

top

FAQ QuestionIs one width better than another when it comes to wood floor planks and strips?
FAQ Answer
No, it comes down to what you prefer. Most people say a narrow board will give you a formal look and a broad board will give you a more country feel.
top

FAQ QuestionHow do I remove dried adhesive from the surface of my wood flooring after installation?
FAQ Answer
If the adhesive has dried, use a little drop of mineral spirits and a soft cloth to wipe off. Do not pour the mineral spirits directly on the floor. Wipe off with a damp cloth afterwards. If the adhesive is still wet, simply use water and a soft cloth.
top

FAQ QuestionCan I walk on my wood floor and mop it immediately after installation?
FAQ Answer
If the floor was prefinished and no glue was used in the installation it is okay to walk on or damp mop it immediately after installation. However, if you had to finish your floor after installation or if it was a glue down installation, you should not walk on or mop it for as long the manufacturer recommends.
top